Anti-Microbial Marine LonCoin II Flecks Topseal Vinyl Rolls 6 x 60 Ft

1. 15-micron wear layer vinyl flooring
2. Coin top surface
3. Marine use
4. Stain, soil, scuffing resistant
5. Anti-microbial
6. Directional design
7. Low VOC
8. GreenAir® and GreenMedic®

LonCoin® II Flecks Topseal Vinyl Flooring - Style And Durability

LonCoin II flecks topseal flooring is easy to care for and designed to endure wear, staining, and scuffing. Its coin surface marries traction with style.

The LonCoin II flecks Topseal from Lonseal has a coin surface embossing that provides an outstanding directional design, giving it a nice touch that delivers style and traction. This Lonseal coin flooring adds a stunning splash of coloration that offers camouflage for easier care.

Topseal is Lonseal's® factory-applied urethane finish that guards the floor, lessens scuffing and streamlines routine maintenance. Topseal is applied in a 15-micron wear layer and prolongs the life of the flooring by protecting it from wear due to staining, soiling, and scuffing. It is also durable and functional.

This LonCoin II flooring can be used for multiple settings and applications, from exhibits and entertainment venues, military, marine, ambulance flooring, sprinter van flooring, emergency vehicle flooring, command vehicle flooring, mobile clinics, veterinary settings, medical facilities, dental clinics, bookmobile trailers, bloodmobile settings, and more. It’s durable, versatile, robust, and antimicrobial.

Specs And Features

This flooring is stain, soil, and scuff resistant. It boasts a directional design, is antimicrobial, low VOC, GreenAir, and GreenMedic. It comes in flooring rolls that are 6 feet wide and 60 feet long. The rolls have an overall thickness of 0.100 inch and a wear layer thickness of 0.032 inch. Each roll offers 360 square feet of coverage and has a total weight of 305 pounds.

A Green Product With LEED Points

This Lonseal flooring product qualifies for the Indoor Environmental Quality Credit. This credit shows that the product meets the General Emissions Evaluation and VOC content requirements. The product boasts FloorScore® certification from the Resilient Floor Covering Institute (RFCI) and Scientific Certification Systems which independently test and certify flooring products for compliance with indoor air quality emission requirements. It also meets the standards for the Collaborative for High Performance Schools (CHPS), a green building rating program especially designed for schools.

Other points and qualifications include:
LEEDv4 Contribution towards Building Product Disclosure and Optimization: Environmental Product Declarations Option 1* (0.5 point), LEEDv4.1 Contribution towards Building Product Disclosure and Optimization: Environmental Product Declarations Option 1* (1 point), LEEDv4/4.1 Contribution towards Building Product Disclosure and Optimization: Sourcing of Raw Materials Option 2** (1 point), LEEDv4/4.1 Contribution towards Low-Emitting Materials*** (3 points), 10%-20% Pre-Consumer (Post-Industrial), Recycled Content FloorScore® CERTIFIED Indoor Air Quality Certified to SCS-EC10.2-2007, GREENAIR® (Low VOC's formulated), and GREENMEDIC® (Anti-microbial formulated).

The LonCoin II meets FMVSS 302: CFR 49 §571.302 Flammability of Interior Materials and features exclusive Lonseal Formulations Topseal, GreenAir, and GreenMedic.

Installation Process

The information below is for a typical flooring installation. Contact the team at Greatmats for marine installation instructions.

1. Make relief cuts as necessary to fit the floor to the installation area.
2. If required, apply Lonseal DFT at seam locations.
3. For simple rooms or installations, select the sheet nearest the wall or perimeter and tube (gently fold the flooring over itself lengthwise) towards the center of the room. Take care, and keep the radius large when tubing the material. Failure to do so could result in damage to the flooring, and visual imperfections may appear on the surface.
4. Spread the appropriate adhesive over the substrate, and after sufficient open time, roll the flooring into the adhesive.
5. After anchoring the first section down, tube the other half of the sheet, and the adjacent sheet, if present. Spread the adhesive over the substrate and seam location, including any DFT. After sufficient open time, roll the flooring into the adhesive, removing the DFT liner beforehand.
6. Continue until the entire area is fully adhered.
7. Trim seams if necessary, and roll the flooring securely into the adhesive or DFT with a hand roller.
8. Heat or chemical weld the seams. Do not heat weld seams less than 24 hours after installation, unless DFT was used.

Cleaning & Maintenance

Initial Maintenance:

1. Ensure the installation has been done per the Interior Flooring Manual and all related technical information.
2. Always wait 48 hours after installation has been completed before beginning initial maintenance.
3. Clean the flooring using a microfiber dust mop. If necessary, vacuum the floor to first pick up any large particles.
4. Using a properly diluted neutral pH cleaner, scrub the floor with a red buffing pad on a slow speed (175 – 300 RPM) rotary floor machine or auto-scrubber, vacuuming up any remaining cleaning solution.
5. If necessary, use clean water and a clean microfiber mop pad to remove any remaining residue.

Routine/Daily Maintenance:

1. Remove all gross soiling (food, gum, residues, etc.). Take care if using a scraper or putty knife to avoid permanently damaging the surface of the flooring.
2. Clean the flooring using a microfiber dust mop. If necessary, vacuum the floor to first pick up any large particles.
3. Apply a properly diluted neutral cleaner to the surface using a microfiber wet mop pad.
4. If necessary, use clean water and a clean microfiber mop pad to remove any remaining residue.

Periodic Maintenance:

1. Remove all gross soiling (food, gum, residues, etc.). Take care if using a scraper or putty knife to avoid permanently damaging the surface of the flooring.
2. Clean the flooring using a microfiber dust mop. If necessary, vacuum the floor to first pick up any large particles.
3. Using a properly diluted neutral pH cleaner, scrub the floor with a red buffing pad on a slow speed (175 – 300 RPM) rotary floor machine or auto-scrubber, vacuuming up any remaining cleaning solution.
4. If necessary, use clean water and a clean microfiber mop pad to remove any remaining residue.

Shipping

This Product Ships Freight Only.
Please review our shipping disclaimer.

Ask a question