LonEquator® Vinyl Flooring - GreenAir® technology

1. Axis Aircraft Collection
2. Variously scaled coin-stamping
3. Aircraft use
4. Reduces risk of slipping
5. Lowers VOC
6. GreenAir®
7. Antimicrobial
8. Phthalate free

LonSeal® LonEquator® Aircraft Coin Dot Flooring

LonSeal® LonEquator® aircraft coin dot flooring is a slip-resistant, 8x60 foot decorative product that offers superior traction. It is part of the Axis Aircraft collection.

These 8x60 feet lonseal flooring rolls are coin-stamped with an assortment of colors and design options. This sheet vinyl covering is a decorated product featuring variously scaled coin-stamping while delivering an assortment of colors and design options. It’s among the best available, anywhere.

The LonEquator® slip resistant flooring gives a different look to coin-stamp offerings by presenting a matte surface and smaller coin pattern for better refinement and a more modern style.

It’s an antimicrobial and phthalate free product that lowers VOC and offers GreenAir benefits. It’s part of the Axis Aircraft Collection made of vinyl material. If this flooring is in place, there is no need for an extra mat where traction is needed.

This commercial grade, sheet vinyl flooring boasts a modern style with its smaller coin pattern. Available in hillcrest tan, black star, santorini blue, and stormy sky, each roll is 8 feet wide by 60 feet long and 2.3mm thick. Each roll provides 480 square feet of coverage and carries with it a limited manufacturer warranty.

LonSeal® LonEquator® Aircraft Coin Dot Floor Covering Specs & Features

This aircraft coin dot floor covering is suitable for anything from a plane or helicopter to a blimp and more. Some commercial and specialty vehicles may also utilize this product, as it is very durable and versatile.

Each Lonseal aircraft floor covering comes in a roll that is 8 feet wide and 60 feet long. You can use the convenient calculator at the top of the page to figure out the exact amount of product you will need, or, you can reach out to the team at Greatmats for help determining this. Each roll will provide 480 square feet of coverage.

Each of the Lonseal flooring rolls weighs approximately 290 pounds. It’s a product made of very durable vinyl with an embossed finish, and coin textured pattern. It features an overall thickness of 0.092 inches or 2.3 mm and a wear layer thickness of 0.032inches or 0.8 mm.

LonSeal® LonEquator® Aircraft Coin Dot Flooring - Environmentally Intelligent Flooring

This aircraft coin dot flooring is a safe, clean, eco-friendly product. It is both phthalate free and SVHC free, low VOC, antimicrobial, and REACH. It’s a product that is GreenAir®, GreenMedic®, and Featherweight. It meets FAA requirements for FAR 25.853a - 12-second vertical flammability test and FAR 25.793 - factor of sliding friction.

LonSeal® LonEquator® Aircraft Coin Dot Flooring - The Installation Method:

1. Acclimate products to the application location for a minimum of 48 hours prior to installation.


2. Loose lay the flooring, and make any relief cuts as necessary.


3. Apply a bead of joint sealant between the floor panels if required, and allow the sealant to fully cure per the manufacturer’s recommendations. Apply seam tape centered on the seam once cured, smoothing the tape against the substrate to avoid air bubbles.


4. Install the moisture barrier tape following the manufacturer’s guidelines.


5. Apply a full spread of Lontape to the substrate. Do not overlap the tape and minimize gapping.


6. Right before you’re ready to place the flooring, remove the tape liner.


7. Place the flooring into the tape, making sure to align any patterns at the center or focal point of the installation area. Minimize any repositioning of the flooring after placing it into the tape, as each repositioning may result in a weaker overall bond.


8. Roll the flooring in both directions using a minimum 100 lb. (45.4 kg), three-section roller.


9. To ensure a proper fit, trim any excess flooring.


10. Heat weld all seams of adjacent flooring, except for flooring that is too heavily embossed to be properly heat welded.


11. Apply sealant around the perimeter of the installation and any exposed edges of the flooring following the manufacturer’s guidelines.


12. Once the tape and perimeter sealant (if used) has cured, perform initial maintenance.

LonSeal® LonEquator® Aircraft Coin Dot Flooring - Appropriate Maintenance & Cleaning:

Initial Maintenance

• Once installed and 48 hours have passed, clean the flooring using a microfiber dust mop.


• If necessary, vacuum the floor to first pick up any large particles.


• Using a neutral pH cleaner, scrub the floor with a red buffing pad on a slow speed rotary floor machine or auto-scrubber and vacuum up any remaining cleaning solution.

Routine/Daily Maintenance

• Remove all soil, dirt, dust, and debris.


• Clean the aircraft flooring using a microfiber dust mop. If necessary, vacuum the floor first.


• Apply a diluted neutral cleaner to the surface using a microfiber wet mop pad.


• If necessary, use clean water and a clean microfiber mop pad to remove any remaining residue.

LonSeal® LonEquator® Aircraft Coin Dot Flooring - A Great Aircraft Flooring Solution

This commercial grade aircraft flooring product is a high performing, attractive solution that is suitable for so many applications. Reach out to the customer service staff at Greatmats for more information, or, for assistance placing your order. This product will look great and perform well in an aircraft for years to come.

Shipping

Ships via freight delivery

This Product Ships Freight Only.
Please review our shipping disclaimer.

Ask a question