LonMarine® Wood Vinyl Flooring - Slip resistant

1. Marine wood vinyl flooring
2. Slip resistance
3. Marine and Speciality Vehicles use
4. Interior or exterior areas of boats
5. Matte or gloss finish
6. Low VOC
7. GreenAir®
8. Phthalate free

LonMarine® Lonseal marine flooring is a high performing, slip-resistant marine safety flooring product that has been precisely manufactured. It is compliant with IMO/MED specifications for international markets, and it is USCG approved. Lonseal marine flooring comes in matte and glossy finishes, and has color coordinating trim.

Suitable for exhibits, entertainment venues, marine applications (boat deck, dock), and specialty vehicles, this faux wood Lonseal flooring with a plank look is slip resistant. That makes it perfect for an interior or exterior area of a boat or any other commercial setting prone to moisture.

Lonseal® LonMarine® Options & Top Features

Lonseal LonMarine sheet vinyl flooring is available in numerous attractive color options - Antique Ivory, Mahogany & Holly, Mahogany, Maple & Teak, Solid Teak, Teak & Ebony, Teak & Holly, Teak & Ivory, Walnut & Holly, and Weathered Teak & Ebony. The marine grade flooring rolls are 6 feet in width, 60 feet in length, and have an overall thickness of 2.0 millimeters. The synthetic wood flooring rolls also have a wear layer thickness of 0.5 millimeters and an overall weight of 260 pounds.

• Flexible construction allowing for moisture-free seams, flash coving, and vertical surface applications


• Low-maintenance finish that eliminates re-finishing expenses


• Durable commercial wear-layer that stands up to years of usage in marine environments


• Variety of patterns and colors available


• Coordinating trim available for hatch covers and access panels


• Trims can also be used for stair nosing


• Lonmarine® Wood - IMO compliance for international markets (MED-Approved Flooring per IMO-SOLAS Requirements) and USCG certified

Lonseal Marine Flooring - Eco-Friendly, Top Notch Standards

Lonseal marine flooring is formulated to guarantee low VOC emissions in its commitment to maintain healthy indoor air quality. It also meets FAA requirements FAR 25.853a: 12-second vertical flammability test and FAR 25.793: Factor of sliding friction. It’s also phthalate and SVHC free.

This marine flooring with realistic wood images is one of the finest quality, environmentally-conscious products available. It meets the highest industry standards in manufacturing and distribution. It’s made by an environmentally-conscious manufacturer and provides the most functional, sustainable, and durable marine flooring available. The flooring features the lowest VOC properties of any vinyl flooring product on the market.

Lonseal Marine Flooring - Installation & Maintenance Method

1. Prepare the approved substrate. Marine Exterior grade plywood falls under APA Plywood Underlayment Panels per their Document E30 and is acceptable for use. Any plywood panels used must be untreated.


2. Ensure all products have been properly acclimated prior to installation. When installations are not performed in a controlled environment, dimensional changes with the flooring, and differing adhesive open, working, and curing times, must be taken into consideration.


3. Apply a full spread of approved adhesive using a 1/16 x 1/32 x 1/32 in. (1.6 x 0.8 x 0.8 mm) U-notch trowel and place the flooring into the adhesive immediately.


4. Roll the flooring using a minimum 100 lb. (45.4 kg), three-section roller. Roll the floor again 2 to 3 hours later. If unable to utilize a large roller due to the size of the vessel or accessibility, a three-section laminate roller may be used. When using a smaller roller, the installer must put enough weight behind it to ensure strong, positive contact.


5. Heat weld all seams 24 hours after installation.


6. If installing Lonmarine® Trim, allow the adhesive to cure prior to installation.


7. Perform initial maintenance 48 hours after installation.

Once the flooring is installed, take care to follow the proper maintenance guidelines.

1. Remove all gross soiling (food, gum, residues, etc.). Take care if using a scraper or putty knife to avoid permanently damaging the surface of the flooring.


2. Clean the surface with a microfiber dust mop pad.


3. Apply a properly diluted neutral cleaner to the surface using a microfiber wet mop pad. Only use neutral cleaners intended for sheet vinyl to clean the flooring. Use of other types of cleaners, even diluted bleach or ammonia, could cause permanent damage, like discoloration or staining.


4. A scrubbing pad may be used instead of a microfiber wet mop to clean the floor to address heavy soiling.


5. If necessary, use a clean microfiber mop pad and clean water to remove any remaining residue.


6. Allow the floor to fully dry.


7. Initial maintenance is the best time to apply a finish, if one is desired. Refer to the appropriate Maintenance Guide if intending to apply a finish.

Lonseal Marine Flooring - The Best On The Market

This top notch, commercial grade marine flooring product is a high performing, attractive solution that is suitable for so many applications. It offers a sea-hardy surface that provides customers with finishes that are as economical as they are exhilarating. With an unparalleled range of striking sound-dampening and cushioned-step surfaces – and unrivaled dimensional patterns that have proven themselves in countless installations – one of the Lonseal surface solutions would perfectly suit all of your nautical flooring needs.

For more information, reach out to the customer service team at Greatmats. They can answer your questions and offer assistance placing your order.


IMO/MED AND USCG COMPLIANT

MEETS IMO/MED 2014/90/EU

USGC CERTIFIED

FEATURES (data shown is nominal):
Roll Width: 6 ft. (1.8 m)
Roll Length: 60 ft. (18.3 m)
Overall Thickness: 0.080 in. (2.0 mm)
Wear Layer Thickness: 0.020 in. (0.5 mm)
Weight: 0.7 lbs./sq. ft. (3.4 kg/m²)

EU REACH COMPLIANT FORMULATION:
Phthalate free, SVHC free

EXCLUSIVE LONSEAL® FORMULATIONS:
GreenAir®

WARNING: California Proposition 65

**Only for fully interior installations.  If marine flooring is installed in a semi-exterior installation, a finish is not typically applied, but routine maintenance should still be performed as noted.  If interested in using a finish on a semi-exterior installation, please contact Greatmats Customer Service for more information. Shipping

Ships via freight delivery

This Product Ships Freight Only.
Please review our shipping disclaimer.

Ask a question